Lighting Configuration: Back Illuminated Sign Panel
Ex db IIC Gb, Ex tb IIIC Db IP66
Battery Backup Runtime: 3 Hours
Ta = -20°C to +60°C
Battery Backup: Nickel Cadmium Battery Pack
Faceplate Color: Copper Free Aluminum Housing
3 Hour Emergency Runtime
Materials: Red or Green
Mounting: Ceiling Mount, Pendant Mount, Wall Mount
Wiring: 3/4" NPT Wiring Hub
Toll Free: 1-800-369-6671
Made in the USA
The ATEX-EXP-EMG-EXT-LE6-1L-50HZ Explosion Proof LED Exit Sign with emergency battery back up from Larson Electronics is Class I, Divisions 1 & 2, Groups B, C, D, Class I, Zones 1 & 2, Groups IIB+H2, IIA, Class II, Divisions 1 & 2, Groups E, F, G and Class III Divisions 1 & 2 rated for hazardous areas. Equipped with a 1.1 watt LED lamp, a 3 hour runtime and self diagnostic system, this failsafe exit sign helps show workers within hazardous environments where the exit is during power failures. This single sided exit sign is an ideal emergency exit marking solution for hazardous locations where failsafe reliability is a must.
The ATEX-EXP-EMG-EXT-LE6-1L-50HZ is an effective option for operators who wish to ensure their hazardous workspaces employ the most up to date and reliable means of marking emergency exit-ways available. Under normal conditions this emergency exit lamp uses normal external power to illuminate its 1 watt LED array. In the case of power outages or in any situation where power is interrupted, this unit automatically switches to a battery backup which will power the unit for three hours or until power is restored. This fixture has three mounting options and is multi-voltage capable.
Light Features: The ATEX-EXP-EMG-EXT-LE6-1L-50HZ features a backlit LED array that each contain eight LEDs, drawing a total of 1.1 watts. This explosion proof emergency LED fixture features brown-out, short circuit and voltage surge protection and has a low voltage disconnect which prevents damage to the battery caused by a deep discharge. This self-testing LED fixture will run for a minimum of 3 hours after a power failure thanks to the maintenance-free 3.6 volt NiCad battery. After emergency use, the battery takes 24 hours to completely recharge.
Click Photo to Enlarge
This emergency exit marking fixture is explosion proof and carries an integral battery backup power supply. When external power is cut due to outages or accidents this lamp automatically switches to its battery backup which will power the lamp for three hours, longer than the requirements specified in the NFPA 101. The ATEX-EXP-EMG-EXT-LE6-1L-50HZ sign panel is back illuminated by LEDs and as a result draws only 1.1 watt of power and has an extreme LED luminary lifespan rated at 15 years. This fixture is approved for outdoor use and is resistant to saltwater making it suitable for use in marine environments.
Emergency Operation: The ATEX-EXP-EMG-EXT-LE6-1L-50HZ features a backup battery that will run the fixture for at least 90 minutes following a power outage or any other loss of power. The included emergency backup battery is a 3.6 volt NiCad rechargeable unit. These batteries are maintenance-free and have a life expectancy of 15 years while being able to operate in a wide variety of conditions including in temperatures ranging from 0°C to +40°C. This unit also features a low voltage disconnect. This means that if the fixture detects that the battery`s terminal voltage has fallen below a certain level, the low voltage circuit will disconnect the emergency lighting load until normal power is restored. This prevents the battery from experiencing a deep discharge and becoming damaged.
Wiring: The ATEX-EXP-EMG-EXT-LE6-1L-50HZ explosion proof emergency self-testing LED fixture is NOT a factory sealed fixture. Operators will bring their own wiring to a junction box and complete their connects. The operator will also provide their own seal off for this fixture. The ATEX-EXP-EMG-EXT-LE6-1L-50HZ operates on 220/240V AC at 50Hz.
Mounting: The EXP-EMG-2L-LE6 is designed to be surface mounted to flat surfaces such as walls. The unions connecting the upper lamps to the lower indicator light enclosure allow for both horizontal and vertical adjustment. This gives operators the ability to adjust the light to their specific mounting location for ideal light coverage during a power failure or power outage.
Suggested Applications: The EXP-EMG-2L-LE6 is designed to for use within hazardous environments to mark the exit-ways of rooms and buildings.
Made in the USA Quality
Superior LED Benefits
1. Uniform LED illumination
2. Battery Replacement Notification Built In
3. Universal 220V/240V AC Selectable
4. 3 Hour Battery Backup Runtime
5. Copper-free aluminum housing
6. 3/4€ NPT conduit hubs
7. Maintenance free
8. 15 Year LED Rated Lifespan
9. Fully Automatic Operation
10. Self Testing System
11. High Intensity LEDs
12. Low Power Consumption (1.1 watts)
13. Fully Electronic Circuit Control
1. Extreme long life.
2. High efficiency and low amp draw.
3. High durability and reliability.
4. Small size and light weight.
5. 100% recyclable.
6. No toxins-lead, mercury.
7. High light output.
8. Consistent color over time.
9. High Versatility.
10. No fragile glass used in construction.
12. Vibration/impact resistant.
Shipping and delivery Information
Estimated delivery times range from 1 to 3 weeks, depending on your location, the product ordered and stock availability. External factors such as courier network disruptions can also impact delivery timelines. PuriLite strives to ship your purchase in the shortest possible time using industry standard courier services.
For any questions related to shipping and delivery, please call 1-844-787-5483, email us at firstname.lastname@example.org or chat with us by clicking on the chat icon at the bottom right of this page.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Return & Refund Policy
For All non-Larson Products If you are not satisfied with a product, contact us by emailing or call 1-844-787-LITE within 30 days of receipt. A refund may be arranged excluding freight charges upon inspection. Returned merchandise must be shipped in original packaging, freight prepaid, unused, and in resalable condition, and are subject to 25% restocking fee. PuriLite inspects all returns and reserves the right to refuse credits on damaged, used or non-resalable items. Your only obligation is the freight charge and restocking fee, provided your return is complete with original packaging, all documentation, warranty cards, cables etc. PuriLite reserves the right to authorize product returns after 30 days have passed from the order date. If the product is accepted after this period, it is subject to a 25% restocking fee and credit will be issued toward future purchases only.
Shipping and handling charges are non-refundable for all returns. The customer may also be responsible for return shipping charges, insurance and shipment tracking for returned merchandise.
Once you place an order, the following products are non-returnable: custom-cut, customer built or special order items (such as matting, slings, cranes, prefab offices, buildings, mezzanines, assembled lockers and regularly stocked items such as generators, pressure washers, water and trash pumps, snow throwers, radio headsets, striping paint, line stripers, floor care machines, vacuums, custom fabric chairs, forklifts) your order is considered non-cancellable and any custom-cut, customer built or special order items purchased by you are also non-returnable. Consumable style bulbs or lamps are not returnable. There are no returns on any medical and/or sanitizing products for obvious safety reasons. This includes PPE (including masks), tests, thermometers, sprayers and UVC lighting of any kind (portable and surface).
Leased and hazardous items are also non-returnable. Contact customer service for a complete list of applicable products.
Larson product return policy Every order is tested prior to shipping. The product is tested before it is put into the shipping box, crate, pallet, etc. Larson take pictures and videos of every product for every order being shipped, and store these pictures and videos with the order number in our system. Because of the complexity of some of our products, we have a very limited return policy.
For safety reasons, we do not accept returns on any hazardous location, explosion proof or intrinsically safe products. Once these products leave the factory, we cannot be sure what happens to them. We must re-build and re-certify the units to specification to ensure that the next customer receives an item that is safe to use. This is cost prohibitive. For that reason, we do not accept returns on classified products. We do not accept returns on transformers, phase converters, or frequency converters. In order to install one of the aforementioned products, typically customers will modify the product (i.e. penetrate the housing to make connections, punch out knockouts, remove or damage tinning on lead wires during installation). Because we video test every unit before it ships to ensure the unit operates as described, we know when they leave here the units are operationally functional and meet the output voltage when supplied with the input voltage per the product specification. To be clear, we do not accept returns on these items under any circumstances for these reasons.
Products that are not addressed in the above two conditions must be returned in new, unused condition.
Below are some additional considerations:
Electrical/electronic parts are easily damaged by improper installation or testing. Because electronics are very sensitive to voltage overloads, it does not take much of a voltage spike to ruin a component. Because of this risk, all electrical products returned will undergo electrical testing and assessed a testing fee. This fee will be subtracted from the final return value.
Consumable style bulbs or lamps are not returnable.
Products that contain emergency backup components are subject to very narrow warranty terms and do not qualify for return. For customer convenience, we engage the battery pack prior to shipping all emergency backup products. Many times, particularly with hazardous location rated products, the battery packs are difficult to access and the customer generally plans to install the units shortly after receipt of the shipment. Battery backup components using older technologies (Nicad, NIMH, SLA, etc) will fail quickly if they do not maintain valid grid tie support. In other words, the batteries must receive a consistent maintained charge to perpetuate long lifespans. Battery backup products that are shelved (not installed) for periods greater than 3 weeks will likely fail and need replacement sooner. This replacement will not be covered under warranty. This can also occur is the units are installed but the grid tie option is not connected correctly. Customers can specify that they do not want the battery pack to be engaged at the time of ordering if they plan to shelve the units for long periods of time prior to installation.
There are many products on the site and not all pictures depict the exact configuration of each product. Many products are custom built and/or built on demand. In some cases, products are designed and not sold immediately and rendering may be used. In all cases, the end product is built to the specification listed and the pictures shown may be close approximations. Pictures are more likely to be close approximations with more complex products, including transformers, power distribution systems, control systems, light tower systems and other highly customizable products. In no way does the approximation validate a potential return. We always build to the specification. If customers have questions, they should ask prior to purchase to clarify.
There are no returns on any medical and/or sanitizing products for obvious safety reasons. This includes PPE (including masks), tests, thermometers, sprayers and UVC lighting of any kind (portable and surface)
Many international orders, specialty orders and other complex build orders require prepayment in advance. This prepayment represents a commitment to the order. Cancelling the order will result in a deduction from the original amount paid if any refund is available, since an investment of time and money is typically required to acquire materials and prepare the order. While not all orders in this category require prepayment, cancellation fees may apply to other build orders as well. The percentage of the deduction is at Larson’s discretion but usually ranges from 30 to 50%.
How to Return For all returns, you can email us at email@example.com. You will need the invoice number in the subject line of the email. You can use one of your preferred carriers. Please note that for freight collect shipments, you are responsible for order tracking once the freight is loaded onto the truck. In addition, PuriLite Industrial cannot assist you with filing damage claims with your carrier.
All returns must be authorized by PuriLite. A Return Authorization Number must be obtained from PuriLite Customer Service Department, and the client must provide the Invoice number at the time of the request. The following conditions must be met. Failure to do so could result in refusal of a shipment by us.
At the time of the return, goods must be a stock item with PuriLite and the returned quantity must correspond to the quantity of the original packaging
Approval and shipping destination must be obtained from PuriLite before returning goods;
Goods must be returned to the appropriate location within 10 working days after receiving the return authorization number;
The return authorization number and invoice number must be identified on the return address label;
Goods must be in their original packaging, arrive undamaged and in resalable form
All returns are to be sent prepaid;
Specially ordered goods are non returnable – these products are identified with a part number beginning with a // on quotes and invoices.
Goods damaged in transit must be signed as damaged by the receiver and carrier at the time of receipt of goods in order to request credit from PuriLite.
PuriLite reserves the right to deny any Returns or Claims if the above conditions are not met.
Orders for products affected by x-factor events such as viral outbreaks and other extreme circumstances CANNOT be returned once shipped and billed.