Surface Mounting:Â (2) Flange Type Aluminum Brackets
Toll Free:Â 1-800-369-6671
Pendant Mounting: (2) 1/2" or 3/4" Threaded NPT Hubs on Either Side
Wiring Hub: (2) 1/2" or 3/4" Threaded Hubs
U.L Approval: Â
Made in the USA
The Larson Electronics HALP-EMG-48-3L-T8 Hazardous Area Fluorescent Light Fixture is U.S./Canada UL Listed Class 1 Division 2 Groups A, B, C and D - UL 1598A listed, has a T4C temperature rating and is specifically designed to handle the rigors of wet and corrosive marine environments.
The HALP-EMG-48-3L-T8 hazardous area fluorescent light fixture is designed for use in wet areas and saltwater-marine environments where corrosion resistance is critical to equipment longevity and safety. This Class 1 Division 2 rated fixture is constructed of non-corrosive materials including a polyester housing reinforced with glass fiber, a poured in gasket for reliable sealing and an impact resistant acrylic diffuser. Corrosion resistant stainless steel latches secure the lamp cover to the housing and provide a firm lock against the poured in seal to prevent drips and water intrusion. This fixture is UL 844 rated and Class 1 Division II, Groups A, B, C, D approved. The HALP-EMG-48-3L-T8 also carries a UL 1598A outdoor marine rating and meets US Coast Guard specifications.
This fluorescent light works, mounts and is wired like our HALP-48-3L-T8 explosion proof fluorescent light fixtures. The main difference is that we add a battery backup unit that adds emergency light functionality to the fixture. This hazardous area emergency light will run the standard UL suggested 90 minutes after power is lost. The light recharges the battery once electrical power is restored. Standard configuration includes a single emergency ballast that will run a single lamp at 900 lumens for 90 minutes. The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.
Click Photo to Enlarge
NOTE ON LAMPS: This fixture comes equipped with F32-T8/841 â€“ 32 Watt lamps producing 2,950 lumens per bulb, a 4100 Kelvin color and a 24,000 hour rated service life. The HALP-EMG-48-3L-T8 has an electronic multi-voltage ballast and works with 120 Volt 60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ and 277 Volts 60 HZ.
Standard Flange Brackets: Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide some shock absorbency protection while enabling the user to simply mount the fixture with the through-hole taps that protrude on each side of the fixture. The mounting holes are 36 9/16 inches on center apart along the top of this hazardous location light. The mounting holes are 7 inches on center across the top of the light.
Pendant Mounting: This light fixture can hang from the ceiling suspected by rigid pipe. Each fixture is equipped with either two 1/2" or 3/4" NPT hubs on either side of the Â fixture. Operators will bring rigid pipe down to the threaded mounting ups. The wiring is fed down through the rigid pipe to one of the NPT hubs and tied to the fixture`s lead wires to complete the electrical connection. The remaining pendant hub provides support for the opposite end of the fixture.
Suggested Applications: The HALP-EMG-48-3L-T8 is designed for marine wet and damp locations, where corrosion resistant fluorescent lights are required. This includes petrochemical facilities, lubrication pits, oil drilling rigs, crew quarters, solvent/cleaning areas, water treatment areas, processing plants and marine loading docks.
Made in USA Quality
1. Each unit dialectically tested.
2. Fixture arrives assembled and lamped to reduce installation time and cost. Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface.
3. Fixture housing constructed of glass fiber reinforced polyester.
4. Relamping done via 6 stainless steel snap locking latches, which enable the operator to remove the door and access the lamps.
5. Lamp cover-diffuser constructed of high impact acrylic for corrosion resistance and lamp protection.
6. 1/2" or 3/4" threaded access hole for wiring conduit.
F32-T8/841 â€“ 2950 lumens per bulb, 24,000 hours life, 4100 Kelvin color
Shipping and delivery Information
Estimated delivery times range from 1 to 3 weeks, depending on your location, the product ordered and stock availability. External factors such as courier network disruptions can also impact delivery timelines. PuriLite strives to ship your purchase in the shortest possible time using industry standard courier services.
For any questions related to shipping and delivery, please call 1-844-787-5483, email us at firstname.lastname@example.org or chat with us by clicking on the chat icon at the bottom right of this page.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Return & Refund Policy
For All non-Larson Products If you are not satisfied with a product, contact us by emailing or call 1-844-787-LITE within 30 days of receipt. A refund may be arranged excluding freight charges upon inspection. Returned merchandise must be shipped in original packaging, freight prepaid, unused, and in resalable condition, and are subject to 25% restocking fee. PuriLite inspects all returns and reserves the right to refuse credits on damaged, used or non-resalable items. Your only obligation is the freight charge and restocking fee, provided your return is complete with original packaging, all documentation, warranty cards, cables etc. PuriLite reserves the right to authorize product returns after 30 days have passed from the order date. If the product is accepted after this period, it is subject to a 25% restocking fee and credit will be issued toward future purchases only.
Shipping and handling charges are non-refundable for all returns. The customer may also be responsible for return shipping charges, insurance and shipment tracking for returned merchandise.
Once you place an order, the following products are non-returnable: custom-cut, customer built or special order items (such as matting, slings, cranes, prefab offices, buildings, mezzanines, assembled lockers and regularly stocked items such as generators, pressure washers, water and trash pumps, snow throwers, radio headsets, striping paint, line stripers, floor care machines, vacuums, custom fabric chairs, forklifts) your order is considered non-cancellable and any custom-cut, customer built or special order items purchased by you are also non-returnable. Consumable style bulbs or lamps are not returnable. There are no returns on any medical and/or sanitizing products for obvious safety reasons. This includes PPE (including masks), tests, thermometers, sprayers and UVC lighting of any kind (portable and surface).
Leased and hazardous items are also non-returnable. Contact customer service for a complete list of applicable products.
Larson product return policy Every order is tested prior to shipping. The product is tested before it is put into the shipping box, crate, pallet, etc. Larson take pictures and videos of every product for every order being shipped, and store these pictures and videos with the order number in our system. Because of the complexity of some of our products, we have a very limited return policy.
For safety reasons, we do not accept returns on any hazardous location, explosion proof or intrinsically safe products. Once these products leave the factory, we cannot be sure what happens to them. We must re-build and re-certify the units to specification to ensure that the next customer receives an item that is safe to use. This is cost prohibitive. For that reason, we do not accept returns on classified products. We do not accept returns on transformers, phase converters, or frequency converters. In order to install one of the aforementioned products, typically customers will modify the product (i.e. penetrate the housing to make connections, punch out knockouts, remove or damage tinning on lead wires during installation). Because we video test every unit before it ships to ensure the unit operates as described, we know when they leave here the units are operationally functional and meet the output voltage when supplied with the input voltage per the product specification. To be clear, we do not accept returns on these items under any circumstances for these reasons.
Products that are not addressed in the above two conditions must be returned in new, unused condition.
Below are some additional considerations:
Electrical/electronic parts are easily damaged by improper installation or testing. Because electronics are very sensitive to voltage overloads, it does not take much of a voltage spike to ruin a component. Because of this risk, all electrical products returned will undergo electrical testing and assessed a testing fee. This fee will be subtracted from the final return value.
Consumable style bulbs or lamps are not returnable.
Products that contain emergency backup components are subject to very narrow warranty terms and do not qualify for return. For customer convenience, we engage the battery pack prior to shipping all emergency backup products. Many times, particularly with hazardous location rated products, the battery packs are difficult to access and the customer generally plans to install the units shortly after receipt of the shipment. Battery backup components using older technologies (Nicad, NIMH, SLA, etc) will fail quickly if they do not maintain valid grid tie support. In other words, the batteries must receive a consistent maintained charge to perpetuate long lifespans. Battery backup products that are shelved (not installed) for periods greater than 3 weeks will likely fail and need replacement sooner. This replacement will not be covered under warranty. This can also occur is the units are installed but the grid tie option is not connected correctly. Customers can specify that they do not want the battery pack to be engaged at the time of ordering if they plan to shelve the units for long periods of time prior to installation.
There are many products on the site and not all pictures depict the exact configuration of each product. Many products are custom built and/or built on demand. In some cases, products are designed and not sold immediately and rendering may be used. In all cases, the end product is built to the specification listed and the pictures shown may be close approximations. Pictures are more likely to be close approximations with more complex products, including transformers, power distribution systems, control systems, light tower systems and other highly customizable products. In no way does the approximation validate a potential return. We always build to the specification. If customers have questions, they should ask prior to purchase to clarify.
There are no returns on any medical and/or sanitizing products for obvious safety reasons. This includes PPE (including masks), tests, thermometers, sprayers and UVC lighting of any kind (portable and surface)
Many international orders, specialty orders and other complex build orders require prepayment in advance. This prepayment represents a commitment to the order. Cancelling the order will result in a deduction from the original amount paid if any refund is available, since an investment of time and money is typically required to acquire materials and prepare the order. While not all orders in this category require prepayment, cancellation fees may apply to other build orders as well. The percentage of the deduction is at Larson’s discretion but usually ranges from 30 to 50%.
How to Return For all returns, you can email us at email@example.com. You will need the invoice number in the subject line of the email. You can use one of your preferred carriers. Please note that for freight collect shipments, you are responsible for order tracking once the freight is loaded onto the truck. In addition, PuriLite Industrial cannot assist you with filing damage claims with your carrier.
All returns must be authorized by PuriLite. A Return Authorization Number must be obtained from PuriLite Customer Service Department, and the client must provide the Invoice number at the time of the request. The following conditions must be met. Failure to do so could result in refusal of a shipment by us.
At the time of the return, goods must be a stock item with PuriLite and the returned quantity must correspond to the quantity of the original packaging
Approval and shipping destination must be obtained from PuriLite before returning goods;
Goods must be returned to the appropriate location within 10 working days after receiving the return authorization number;
The return authorization number and invoice number must be identified on the return address label;
Goods must be in their original packaging, arrive undamaged and in resalable form
All returns are to be sent prepaid;
Specially ordered goods are non returnable – these products are identified with a part number beginning with a // on quotes and invoices.
Goods damaged in transit must be signed as damaged by the receiver and carrier at the time of receipt of goods in order to request credit from PuriLite.
PuriLite reserves the right to deny any Returns or Claims if the above conditions are not met.
Orders for products affected by x-factor events such as viral outbreaks and other extreme circumstances CANNOT be returned once shipped and billed.